How to Measure for a New Door Lock: What to Check and Bring to Our Olathe Counter

Brass and silver keyed lever lockset installed on a white door

Picking out new door hardware looks simple until you get it home, hold it up to the door, and nothing lines up. The holes are in the right place but the bolt is too short. Or the lever points the wrong direction. Or the new lock works fine, but now you are carrying a second key for one door while the rest of the house still uses the old one.

All of that is avoidable. Before you shop, there are four things to figure out: backset, door thickness, handing, and how the door is already drilled. Below is how we walk people through it at our walk-in shop in Olathe, plus how to keep your new hardware on the key you already carry.

Start With the Backset: the Measurement People Skip

The backset is the distance from the edge of the door to the center of the big round hole where the knob, lever, or deadbolt sits. Hook your tape on the door edge and measure straight across to the middle of that hole.

In homes around Olathe and the rest of Johnson County, you will almost always land on one of two numbers: 2-3/8 inches or 2-3/4 inches. Both are standard in American residential construction, and most retail lock sets come with an adjustable latch that can be set either way. The trouble starts when the latch in the box is not adjustable, or when the door has an odd backset left over from a remodel or a custom slab.

A few notes from the counter:

  • Measure the door, not the frame. The strike plate on the jamb can be shimmed or moved; the hole in the door cannot.
  • If you have a knob and a deadbolt on the same door, measure both. They do not always match, especially on doors that were re-drilled after the fact.
  • Commercial and older mortise locks do not follow this rule at all. If the lock body slides out of a deep pocket in the door edge instead of sitting in a round hole, bring the whole lock in so we can see what you have.

If you are not sure you measured right, take the old lock off and bring it with you. The hardware in your hand answers the question in seconds.

Door Thickness, Latch Face, and the Edge Bore

Next, measure the thickness of the door at the edge. Most exterior doors in this area are 1-3/4 inches thick. Most interior doors are 1-3/8 inches. Garage-to-house doors are often fire-rated and run the thicker size. Lock sets have a thickness range they will fit, and a deadbolt tailpiece that is too short for a thick door will feel loose or will not throw all the way.

While you are at the edge of the door, look at the metal plate around the latch itself. It is one of three styles:

  • Square corner, usually with a 1-inch by 2-1/4 inch face.
  • Radius corner, rounded to match a router template. The common radius sizes are 1/4 inch and 5/8 inch.
  • Drive-in, with no face plate at all, just a round collar pressed into the edge bore. These show up often on steel and fiberglass entry doors.

Snap a photo of the door edge with your phone before you take anything apart. That one picture tells us the face plate style, whether the mortise for the plate was cut square or rounded, and how tall the bolt pocket is. It can save you a second trip.

The edge bore (the hole the latch slides into) is typically 1 inch across, and the cross bore (the big hole for the lock body) is typically 2-1/8 inches. If your door has a smaller cross bore, you may be looking at older hardware that does not match current standard prep, and that is worth sorting out before you buy anything.

Handing: Which Way the Door Swings and Why It Matters

Handing trips up more people than backset does. Knobs and most residential levers are reversible, so handing feels optional until you buy a lever you cannot flip, a storm door closer, or anything commercial grade.

Here is the simple way we describe it: stand on the outside of the door, the side you would use a key on. If the hinges are on your left, it is a left-hand door. If the hinges are on your right, it is a right-hand door. If the door swings toward you from that position instead of away, add the word reverse.

Exit devices, closers, mortise locks, and some lever sets are built for a specific hand or need to be converted before install. If you are replacing hardware on a business entry in Olathe or anywhere in Johnson County, write down the handing before you shop. It is the one detail that turns a simple swap into a return.

One extra thing to check on storm doors and screen doors: the lock bore on those is usually smaller and set at its own backset, and the hardware is not interchangeable with entry door hardware. Bring the piece in if you are unsure.

Matching New Hardware to the Keys You Already Carry

This is the part people wish they had asked about first. You can put a new deadbolt or entry set on a door and still have it open with the key already on your ring. New hardware does not have to mean a new key.

What makes it work is the keyway and the cylinder. If the new lock uses the same keyway family as your existing locks, we can rekey the new cylinder to your current key at the counter. Do not try to guess compatibility from the outside of the box. Bring the key with you and bring one of your existing cylinders if you can get it off the door.

A few habits that make this go smoothly:

  • Bring every lock you want on one key at the same time. Matching is done as a set, so one cylinder showing up later means handling it twice.
  • Bring the original key, not a worn copy of a copy. A tired key teaches the new lock the wrong depths and the result feels sticky.
  • Tell us about doors you are keeping. If the new front deadbolt needs to match the back door and the garage entry, we need to know that before we start cutting.
  • If the door is a rental, a recently bought home, or had contractors in and out, think about whether you actually want the old key carried forward.

Keypads and electronic locks follow the same rule. Most of them still have a mechanical cylinder for backup, and that cylinder can usually be matched to the rest of the house so the backup key is not a mystery key living in a drawer.

What Olathe Doors Actually Need, Season to Season

Kansas weather is hard on exterior doors, and a lot of lock complaints in Johnson County are really door complaints. Our summers are hot and humid and our winters swing cold, so wood doors and jambs move through the year. A latch that drags in August but is fine in February usually means the door or frame shifted, not that the lock failed.

Before you replace hardware, look at the strike plate. If the latch is scraping the bottom or top edge of the strike opening, the fix may be a longer screw into the framing, a strike adjustment, or shaving the strike opening, not a new lock. We would rather tell you that than sell you hardware you do not need.

Two more things we see on local doors:

  • Short strike screws. A deadbolt is only as strong as what the strike is anchored to. Long screws that reach past the jamb into the framing make a real difference on entry doors.
  • Storm doors in direct sun. A storm door traps heat against an entry door, and that heat can warp a slab over time. If your deadbolt suddenly needs a shoulder to throw, check the door for bow before blaming the bolt.

Finish matters too. Aged bronze, satin nickel, and matte black all live differently outdoors. On a west-facing entry that bakes all afternoon, a finish rated for exterior use holds up better than an interior-grade one that happens to be the right color.

The Counter Checklist: What to Bring to Our Olathe Shop

We have a storefront in Olathe you can walk up to, no appointment needed, and we are an easy drive from Lenexa, Overland Park, Gardner, Shawnee and Spring Hill. When you are coming in for replacement hardware, bring as much of this as you can:

  • The old lock, or the whole handle set, if it comes off easily. Hardware in hand is more reliable than a description.
  • Your measurements: backset, door thickness, and cross bore size if you have it.
  • The handing of the door, written down or shown in a photo.
  • Photos of the door edge, the face of the door, and the strike on the jamb.
  • Every key you want the new lock to accept, plus any other cylinders you want on that same key.
  • A note about the finish on the rest of your hardware if you care about it matching.

If the lock will not come off, or the door is damaged, or you are dealing with a business entry with a closer and an exit device, that is what mobile service is for. We work on site across Olathe and the rest of Johnson County. And if what you really need is a repair or an adjustment rather than new hardware, we will say so. A door that closes right and a key that turns clean are the goal, not a bigger box on the counter.

Ready to move forward? Learn more about our Lock Store or get in touch.

Frequently Asked Questions About Measure for a New Door Lock

How do I measure the backset on my door?

Hook your tape measure on the edge of the door and measure to the center of the large round hole where the lock sits. In most homes the answer is 2-3/8 inches or 2-3/4 inches.

What if my door thickness is not a standard size?

Bring the measurement and the old lock in so we can check the spindle and tailpiece length. Some hardware ships with spacers or longer parts for thicker doors, and some needs a different lock entirely.

Can a new deadbolt work with the key I already have?

Often yes, if the new cylinder uses a compatible keyway. Bring your original key and any other cylinders you want on the same key so they can all be matched together.

How do I tell if my door is left-hand or right-hand?

Stand on the outside of the door where you would use the key. Hinges on your left means left-hand, hinges on your right means right-hand, and add reverse if the door swings toward you.

Do I need new hardware if my latch is sticking?

Not always. Sticking is often a strike plate or door alignment issue caused by seasonal movement, and adjusting the strike or using longer screws can solve it without replacing the lock.

Can I bring the whole door handle into the shop instead of measuring?

Yes. Bringing the hardware itself, or even a drawer front or padlock, lets us see the prep and the keyway directly, which answers most fitment questions without a tape measure.

Need help with Lock Store?

Tell us about your project in Olathe and we will be in touch.

Have a lock, key or safe question?

Call or text 913-390-8200 and tell us what is going on, or stop by the shop at 774 N. Ridgeview Rd in Olathe.